Gression to estimate the location as a function of the following predictor variables: (i) Maximum intensity of the microtubule image, (ii) Mean intensity of the microtubule image, and (iii) pixel intensity of the XY coordinate in the microtubule image. The coefficients of the linear regression were estimated from the 3D HeLa images where the 3D centrosome as described previously [8]. The estimated centrosome is then used to act as an organizer for microtubules and all generated microtubules start from it. Estimation of single microtubule intensity. The single microtubule intensity for 25033180 each cell line was estimated using the method described previously [9]. It is then used to scale the intensity of synthetic image up to that of the real image. 3D cell and nuclear morphology generation. In order to estimate the cell shape, we firstly required the following two estimates: (1) the cell shape at the bottom, where the cell membrane interacts with a substrate (e.g. petri-dish), and (2) cell shape decay from the bottom of the cell to the top. For estimating the bottom shape of the cell, we used the microtubule channel image acquired at the center of the cell, i.e. z = Z/2, where Z is the height of the cell in pixel dimensions. This image contains information about the cell boundary at the bottommost region because the out-of-focus light from the bottom slice is visible in the center slice (as microtubules being of relatively lower intensity). Hence, the boundary of the bottom slice (bottom shape) was found by thresholding for above zero intensity pixels. (see Figure 3 (A) for an example). Next, we represented the cell shape decay by estimating cell shape pixel area as a function of height of the cell, i.e. A(z). This function was estimated from the average area profile of the 2D slices 
in the 3D HeLa stack (data not shown) to be A(z) = 22z*Area, where Area is the pixel area of the bottom slice, and z is the distance from the bottom. Since the cell tapers from the bottom shape to the top (because of the presence of a nucleus), we modeled the 3D cell shape by interpolating from the bottom shape of the cell to a smaller ellipse MedChemExpress TA 01 inside the cell whose major axis was aligned with that of the cell. This interpolation was done using distance transform based shape interpolation [19]. Given the height of the cell and 23727046 the z-sampling step-size (0.2 microns, 1 pixel volume per stack), we discretized this model at varying z by choosing interpolated shapes that have areas that match the estimated area profile A(z) from the 3D HeLa stack. Figure 3 (C) shows an example of generated 3D cell shape containing 8 stacks (height of 1.6 microns). The 3D nuclear morphology was generated based on the same procedure aboveusing the Fexinidazole nucleus channel image (Figure 3 (D)). Then microtubules are generated conditioned on the approximate 3D cell and nuclear shape. Growth model of microtubule patterns. The growth model of microtubule patterns (Figure 1) is similar to the one described previously [8], with three modifications: (i) the Erlang distribution was used for microtubule lengths since, unlike the Gaussian distribution, it has only one free parameter; (ii) if the microtubule is required to make a turn in 3D space such that the 3D angle is greater than 63.9 degrees with cosine value of 0.44 (this value is chosen manually to account for appearance of real microtubules as well as the generability of the model), the growth procedure for it is terminated; and (iii) if within a co.Gression to estimate the location as a function of the following predictor variables: (i) Maximum intensity of the microtubule image, (ii) Mean intensity of the microtubule image, and (iii) pixel intensity of the XY coordinate in the microtubule image. The coefficients of the linear regression were estimated from the 3D HeLa images where the 3D centrosome as described previously [8]. The estimated centrosome is then used to act as an organizer for microtubules and all generated microtubules start from it. Estimation of single microtubule intensity. The single microtubule intensity for 25033180 each cell line was estimated using the method described previously [9]. It is then used to scale the intensity of synthetic image up to that of the real image. 3D cell and nuclear morphology generation. In order to estimate the cell shape, we firstly required the following two estimates: (1) the cell shape at the bottom, where the cell membrane interacts with a substrate (e.g. petri-dish), and (2) cell shape decay from the bottom of the cell to the top. For estimating the bottom shape of the cell, we used the microtubule channel image acquired at the center of the cell, i.e. z = Z/2, where Z 
is the height of the cell in pixel dimensions. This image contains information about the cell boundary at the bottommost region because the out-of-focus light from the bottom slice is visible in the center slice (as microtubules being of relatively lower intensity). Hence, the boundary of the bottom slice (bottom shape) was found by thresholding for above zero intensity pixels. (see Figure 3 (A) for an example). Next, we represented the cell shape decay by estimating cell shape pixel area as a function of height of the cell, i.e. A(z). This function was estimated from the average area profile of the 2D slices in the 3D HeLa stack (data not shown) to be A(z) = 22z*Area, where Area is the pixel area of the bottom slice, and z is the distance from the bottom. Since the cell tapers from the bottom shape to the top (because of the presence of a nucleus), we modeled the 3D cell shape by interpolating from the bottom shape of the cell to a smaller ellipse inside the cell whose major axis was aligned with that of the cell. This interpolation was done using distance transform based shape interpolation [19]. Given the height of the cell and 23727046 the z-sampling step-size (0.2 microns, 1 pixel volume per stack), we discretized this model at varying z by choosing interpolated shapes that have areas that match the estimated area profile A(z) from the 3D HeLa stack. Figure 3 (C) shows an example of generated 3D cell shape containing 8 stacks (height of 1.6 microns). The 3D nuclear morphology was generated based on the same procedure aboveusing the nucleus channel image (Figure 3 (D)). Then microtubules are generated conditioned on the approximate 3D cell and nuclear shape. Growth model of microtubule patterns. The growth model of microtubule patterns (Figure 1) is similar to the one described previously [8], with three modifications: (i) the Erlang distribution was used for microtubule lengths since, unlike the Gaussian distribution, it has only one free parameter; (ii) if the microtubule is required to make a turn in 3D space such that the 3D angle is greater than 63.9 degrees with cosine value of 0.44 (this value is chosen manually to account for appearance of real microtubules as well as the generability of the model), the growth procedure for it is terminated; and (iii) if within a co.
